Линукс и Intel 82599ES 10-Gigabit SFI / SFP + связь всегда отключена

У меня HP ProLiant dl360 gen 9, когда сервер запускается, у меня есть ссылка на Intel 82599ES.
После запуска linux (ядро Slackware 14.2 4.4.19) связь не работает (что-то вроде отключения spf?).
Как я могу это исправить?

# lspci | grep Network 04:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01) 04:00.1 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01)  # ethtool eth0 Settings for eth0: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: Unknown! Duplex: Unknown! (255) Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: umbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: no  # ethtool -i eth0 driver: ixgbe version: 4.2.1-k firmware-version: 0x80000887 expansion-rom-version: bus-info: 0000:04:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: no  # lsmod |grep -E 'ixgbe|mdio|igb|ioat|dca' ixgbe 221749 0 vxlan 34494 1 ixgbe ptp 12164 2 tg3,ixgbe mdio 3973 1 ixgbe ioatdma 33129 0 dca 6585 2 ixgbe,ioatdma hwmon 4199 4 tg3,ixgbe,coretemp,acpi_power_meter  # ethtool -m eth0 Identifier : 0x03 (SFP) Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID) Connector : 0x07 (LC) Transceiver codes : 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Transceiver type : 10G Ethernet: 10G Base-SR Encoding : 0x06 (64B/66B) BR, Nominal : 10300MBd Rate identifier : 0x00 (unspecified) Length (SMF,km) : 0km Length (SMF) : 0m Length (50um) : 80m Length (62.5um) : 30m Length (Copper) : 0m Length (OM3) : 300m Laser wavelength : 850nm Vendor name : FINISAR CORP. Vendor OUI : 00:90:65 Vendor PN : FTLX8571D3BCL-HP Vendor rev : A Option values : 0x00 0x1a Option : RX_LOS implemented Option : TX_FAULT implemented Option : TX_DISABLE implemented BR margin, max : 0% BR margin, min : 0% Vendor SN : MVA0TLN Date code : 16031211 Optical diagnostics support : Yes Laser bias current : 0.000 mA Laser output power : 0.0062 mW / -22.08 dBm Receiver signal average optical power : 0.0000 mW / -inf dBm Module temperature : 28.81 degrees C / 83.86 degrees F Module voltage : 3.3293 V Alarm/warning flags implemented : Yes Laser bias current high alarm : Off Laser bias current low alarm : On Laser bias current high warning : Off Laser bias current low warning : On Laser output power high alarm : Off Laser output power low alarm : On Laser output power high warning : Off Laser output power low warning : On Module temperature high alarm : Off Module temperature low alarm : Off Module temperature high warning : Off Module temperature low warning : Off Module voltage high alarm : Off Module voltage low alarm : Off Module voltage high warning : Off Module voltage low warning : Off Laser rx power high alarm : Off Laser rx power low alarm : On Laser rx power high warning : Off Laser rx power low warning : On Laser bias current high alarm threshold : 13.200 mA Laser bias current low alarm threshold : 4.000 mA Laser bias current high warning threshold : 12.600 mA Laser bias current low warning threshold : 5.000 mA Laser output power high alarm threshold : 1.0000 mW / 0.00 dBm Laser output power low alarm threshold : 0.2512 mW / -6.00 dBm Laser output power high warning threshold : 0.7943 mW / -1.00 dBm Laser output power low warning threshold : 0.3162 mW / -5.00 dBm Module temperature high alarm threshold : 78.00 degrees C / 172.40 degrees F Module temperature low alarm threshold : -13.00 degrees C / 8.60 degrees F Module temperature high warning threshold : 73.00 degrees C / 163.40 degrees F Module temperature low warning threshold : -8.00 degrees C / 17.60 degrees F Module voltage high alarm threshold : 3.7000 V Module voltage low alarm threshold : 2.9000 V Module voltage high warning threshold : 3.6000 V Module voltage low warning threshold : 3.0000 V Laser rx power high alarm threshold : 1.0000 mW / 0.00 dBm Laser rx power low alarm threshold : 0.0100 mW / -20.00 dBm Laser rx power high warning threshold : 0.7943 mW / -1.00 dBm Laser rx power low warning threshold : 0.0158 mW / -18.01 dBm